BitCrane T-110 Setup Guide
|
Contents
0) Introduction 0b) What You Need 1) Powering 2) Cooling 3) Case 4) Configuration 5) Troubleshooting 6) Where to buy |
|
0) Introduction
BitCrane's T-110 features two Golden Nonce ASICs within a really compact case, weighing in at just 9KG. A custom watercooling kit from CoolIT is used to remove heat, while a custom 1100W PSU provides power. An internal Cubie is used as the controller.
BitCrane's T-110 features two Golden Nonce ASICs within a really compact case, weighing in at just 9KG. A custom watercooling kit from CoolIT is used to remove heat, while a custom 1100W PSU provides power. An internal Cubie is used as the controller.
|
Chips
Rated Hash Rate Rated Voltage Rated Current Power Consumption |
- 2x Golden Nonce
- ~1100GH - 12V - 92A - ~1100W |
|
|
0b) What You Need
You will need a few accessories and a power supply to get started.
You will need a few accessories and a power supply to get started.
Click your flag to find everything you need to get started at Amazon!
|
|
|
1) Powering
T-110's come with a custom made 1100W PSU in a standard ATX package. If you wish to replace this, eight PCI-E 6 pin connectors will be required as well as a power supply for the cubie controller board.
T-110's come with a custom made 1100W PSU in a standard ATX package. If you wish to replace this, eight PCI-E 6 pin connectors will be required as well as a power supply for the cubie controller board.
|
|
2) Cooling
Each ASIC is cooling by a custom self contained CoolitIT ECO III-120FB 'BitCrane' watercooling loop - custom made for BitCrane. It features an upgraded pump at 2900RPM compared with the older model at just 2300RPM to allow for greater flow rates. A copper base and aluminium radiator is combined with an AV-12038M12B fan which sucks air into the unit through the radiator, and exhausts it through the side grill. The airflow pattern for the unit is rather unusual.
Noise levels are rather loud for a 1TH unit and may not be appropriate for living rooms, and as of now there does not appear to be any automatic or manual fan control.
Each ASIC is cooling by a custom self contained CoolitIT ECO III-120FB 'BitCrane' watercooling loop - custom made for BitCrane. It features an upgraded pump at 2900RPM compared with the older model at just 2300RPM to allow for greater flow rates. A copper base and aluminium radiator is combined with an AV-12038M12B fan which sucks air into the unit through the radiator, and exhausts it through the side grill. The airflow pattern for the unit is rather unusual.
Noise levels are rather loud for a 1TH unit and may not be appropriate for living rooms, and as of now there does not appear to be any automatic or manual fan control.
|
|
|
|
3) Case
The T-110's case is one of the best I've seen and is extremely lightweight at just 9KG fully loaded. This is mostly due to the lack of required heatsinks, allowing further weight savings throughout the case. The units are not designed to be rack mountable, but do stack on top of each other and lock together. External dimensions of the case are 316 x 425 x 166mm.
The T-110's case is one of the best I've seen and is extremely lightweight at just 9KG fully loaded. This is mostly due to the lack of required heatsinks, allowing further weight savings throughout the case. The units are not designed to be rack mountable, but do stack on top of each other and lock together. External dimensions of the case are 316 x 425 x 166mm.
|
|
4) Configuration
The T-110 is standalone and does not require an external controller.
Wiring:
Software:
Alternative Subnet Change:
The T-110 is standalone and does not require an external controller.
Wiring:
- Plug in an ethernet cable from the T-110 to you router.
- Plug in a power cable from the mains to the PSU. Power on the power supply using its switch at the back.
Software:
- Power on the power supply using its switch at the back.
- Make sure or your router's subnet is 1, ie 192.168.1.x. If not then change it to 1, this is just temporary. ***If this is not possible, see below***
- Using a browser, navigate to 192.168.1.140 - this goes to the T-110's configuration page.
- Make sure popup blocker is off on your browser while your miner configuration page!!!
- Enter your pool information in the below format. Click "Apply and Restart".
- Change IP to an IP of your choice on the subnet of your choice. Set Gateway to the IP of your router. Click Save. You may then need to restart the miner.
- You can then change your router subnet back to whatever you are used to using.
Alternative Subnet Change:
- Unplug your computer from all internet sources.
- Plug in an ethernet cable from the T-110 to your computer.
- Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings.
- Right click on your ethernet adapter -> Properties.
- Click on "Internet Protocol Version 4" and click properties.
- Select "Use the following IP address" and enter the following:
- IP Address: 192.168.1.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.1.140.
- Plug in an ethernet cable from the T-110 to you router.
- Restart the configuration instructions as above.
stratum+tcp://mint.bitminter.com:3333
stratum+tcp://us1.ghash.io:3333
stratum+tcp://stratum.mining.eligius.st:3334
|
|
|
|
5) Troubleshooting
|
Problem
TBD as problems arise |
Solution
|
|
|
6) Where to buy
General Safety Tips
|
Do not touch equipment while powered, exposed electrical contacts may shock.
Fans may cause injury or shatter if material is ingested.
|
|
Sharp edges may be cut, especially around any internal casing or heatsinks.
If you are unsure of what to do, STOP and consult an expert.
|
|
|
|
Legal disclaimer: This information is for general guidance and does not constitute expert advice. We are not responsible if you, your property or a third party is injured or damaged as a result of any interaction with this information, and no warranty is provided. All text and images are covered under copyright law, dogiecoin.com.
|
